stm32_rust/semestralka_1d_rx_bez_dma/src/bin/main.rs

// src/bin/main.rs
#![no_std]
#![no_main]

use defmt::*;
use embassy_executor::Spawner;
use embassy_time::Instant;
use embassy_stm32::dma::Request;
use embassy_stm32::gpio::{Input, Output, Level, Pull, Speed};
use dma_gpio::software_uart::{
    dma_timer::{init_tim6_for_uart, init_tim7_for_uart},
    gpio_dma_uart_rx::rx_dma_task,
    debug::dump_tim6_regs,
};
use dma_gpio::config::{BAUD, RX_OVERSAMPLE, TX_OVERSAMPLE};
use dma_gpio::config::{TX_RING_BYTES, RX_RING_BYTES};
use dma_gpio::software_uart::gpio_dma_uart_tx::tx_dma_task;
use static_cell::StaticCell;
use embassy_futures::yield_now;
use dma_gpio::hw_uart_pc::usart1;
use dma_gpio::hw_uart_pc::driver::uart_task;
use embassy_stm32::usart::{BufferedUart, Config, BufferedInterruptHandler};
use embassy_stm32::peripherals;
use embassy_stm32::bind_interrupts;
use dma_gpio::config::{PIPE_HW_TX, PIPE_HW_RX, PIPE_SW_TX, PIPE_SW_RX};
use embassy_sync::{blocking_mutex::raw::CriticalSectionRawMutex, pipe::Pipe};
use dma_gpio::hw_uart_internal::usart2;
use dma_gpio::hw_uart_internal::driver::uart_task as uart_task_internal;
use dma_gpio::config::{PIPE_INT_TX, PIPE_INT_RX};
use embassy_time::{Duration, Timer};
use {defmt_rtt as _, panic_probe as _};

bind_interrupts!(struct Irqs {
    USART1 => BufferedInterruptHandler<peripherals::USART1>;
});
bind_interrupts!(struct Irqs2 {
    USART2 => BufferedInterruptHandler<peripherals::USART2>;
});

// Software uart
pub const TIM6_UP_REQ: Request = 4;
static SW_TX_RING: StaticCell<[u32; TX_RING_BYTES]> = StaticCell::new();
static SW_RX_RING: StaticCell<[u8; RX_RING_BYTES]> = StaticCell::new();

#[embassy_executor::main]
async fn main(spawner: Spawner) {
    info!("boot");
    let p = embassy_stm32::init(Default::default());
    info!("init m8");
    // HARDWARE UART to the PC
    let mut cfg = Config::default();
    cfg.baudrate = BAUD;
    static TX_BUF: StaticCell<[u8; 256]> = StaticCell::new();
    static RX_BUF: StaticCell<[u8; 256]> = StaticCell::new();
    let uart = BufferedUart::new(
        p.USART1,
        p.PA10, // RX pin
        p.PA9,  // TX pin
        TX_BUF.init([0; 256]),
        RX_BUF.init([0; 256]),
        Irqs,
        cfg,
    ).unwrap();
    let yield_period = usart1::setup_and_spawn(BAUD);
    spawner.spawn(uart_task(uart, &PIPE_HW_TX, &PIPE_HW_RX).unwrap());
    // END OF HARDWARE UART to the PC



    // INTERNAL HARDWARE UART (USART2)
    let mut cfg2 = Config::default();
    cfg2.baudrate = BAUD;
    static TX_BUF2: StaticCell<[u8; 256]> = StaticCell::new();
    static RX_BUF2: StaticCell<[u8; 256]> = StaticCell::new();

    let uart2 = BufferedUart::new(
        p.USART2,
        p.PA3, // RX
        p.PA2, // TX
        TX_BUF2.init([0; 256]),
        RX_BUF2.init([0; 256]),
        Irqs2,
        cfg2,
    ).unwrap();
    let _ = usart2::setup_and_spawn(BAUD);
    spawner.spawn(uart_task_internal(uart2, &PIPE_INT_TX, &PIPE_INT_RX).unwrap());
    info!("USART2 ready");
    // END OF INTERNAL HARDWARE UART (USART2)
    
    // USART1 <-> USART2 bridge
    spawner.spawn(bridge_usart1_rx_to_usart2_tx(&PIPE_HW_RX, &PIPE_INT_TX).unwrap());
    spawner.spawn(bridge_usart2_rx_to_usart1_tx(&PIPE_INT_RX, &PIPE_HW_TX).unwrap());
    info!("USART1 <-> USART2 bridge active");
    // END OF USART1 <-> USART2 bridge 



    // SOFTWARE UART 
    // let _rx = Input::new(p.PD6, Pull::Up);
    let rx_pin = Input::new(p.PD6, Pull::Up);
    // let tx_pin = Output::new(p.PB0, Level::High, Speed::VeryHigh);
    init_tim6_for_uart(p.TIM6, BAUD, TX_OVERSAMPLE);
    init_tim7_for_uart(p.TIM7, BAUD, RX_OVERSAMPLE);
    dump_tim6_regs();
    // EDN OF SOFTWARE UART


    let mut buf = [0u8; 32];
    let mut last_state: u8 = 0;
    loop {
        info!("tick start");

        // RX pin should be READ in here and print via info!
        //
        let bit = rx_pin.is_high();
        info!("Rx_pin read (high): {}", bit);
        if bit as u8 != last_state {
            info!(
                "SW RX -> PD6 changed, new state = {}",
                if bit { "HIGH" } else { "LOW" }
            );
            last_state = bit as u8;
            continue;
            yield_now().await;
        }
        Timer::after(Duration::from_millis(1)).await;
        yield_now().await;
    }
}

#[embassy_executor::task]
pub async fn bridge_usart1_rx_to_usart2_tx(
    usart1_rx: &'static Pipe<CriticalSectionRawMutex, 1024>,
    usart2_tx: &'static Pipe<CriticalSectionRawMutex, 1024>,
) {
    let mut buf = [0u8; 64];
    loop {
        let n = usart1_rx.read(&mut buf).await;
        if n > 0 {
            let _ = usart2_tx.write(&buf[..n]).await;
            info!("bridge: USART1 -> USART2 sent {} bytes", n);
        }
        yield_now().await;
    }
}

#[embassy_executor::task]
pub async fn bridge_usart2_rx_to_usart1_tx(
    usart2_rx: &'static Pipe<CriticalSectionRawMutex, 1024>,
    usart1_tx: &'static Pipe<CriticalSectionRawMutex, 1024>,
) {
    let mut buf = [0u8; 64];
    loop {
        let n = usart2_rx.read(&mut buf).await;
        if n > 0 {
            let _ = usart1_tx.write(&buf[..n]).await;
            info!("bridge: USART2 -> USART1 sent {} bytes", n);
        }
        yield_now().await;
    }
}