rx bez dma ready for testing

semestralka_1e_tx_bez_dma/src/bin/main.rs

@@ -0,0 +1,166 @@
+// src/bin/main.rs
+#![no_std]
+#![no_main]
+
+use defmt::*;
+use embassy_executor::Spawner;
+use embassy_time::{Instant, Timer, Duration};
+use embassy_stm32::dma::Request;
+use embassy_stm32::gpio::{Input, Output, Level, Pull, Speed};
+use dma_gpio::software_uart::{
+    dma_timer::{init_tim6_for_uart, init_tim7_for_uart},
+    gpio_dma_uart_rx::rx_dma_task,
+    debug::dump_tim6_regs,
+};
+use dma_gpio::config::{BAUD, RX_OVERSAMPLE, TX_OVERSAMPLE};
+use dma_gpio::config::{TX_RING_BYTES, RX_RING_BYTES};
+use dma_gpio::software_uart::gpio_dma_uart_tx::tx_dma_task;
+use static_cell::StaticCell;
+use embassy_futures::yield_now;
+use dma_gpio::hw_uart_pc::usart1;
+use dma_gpio::hw_uart_pc::driver::uart_task;
+use embassy_stm32::usart::{BufferedUart, Config, BufferedInterruptHandler};
+use embassy_stm32::peripherals;
+use embassy_stm32::bind_interrupts;
+use dma_gpio::config::{PIPE_HW_TX, PIPE_HW_RX, PIPE_SW_TX, PIPE_SW_RX};
+use embassy_sync::{blocking_mutex::raw::CriticalSectionRawMutex, pipe::Pipe};
+use dma_gpio::hw_uart_internal::usart2;
+use dma_gpio::hw_uart_internal::driver::uart_task as uart_task_internal;
+use dma_gpio::config::{PIPE_INT_TX, PIPE_INT_RX};
+use {defmt_rtt as _, panic_probe as _};
+
+bind_interrupts!(struct Irqs {
+    USART1 => BufferedInterruptHandler<peripherals::USART1>;
+});
+bind_interrupts!(struct Irqs2 {
+    USART2 => BufferedInterruptHandler<peripherals::USART2>;
+});
+
+// Software uart
+pub const TIM6_UP_REQ: Request = 4;
+static SW_TX_RING: StaticCell<[u32; TX_RING_BYTES]> = StaticCell::new();
+static SW_RX_RING: StaticCell<[u8; RX_RING_BYTES]> = StaticCell::new();
+
+#[embassy_executor::main]
+async fn main(spawner: Spawner) {
+    info!("boot");
+    let p = embassy_stm32::init(Default::default());
+    info!("init m8");
+
+    // HARDWARE UART to the PC
+    let mut cfg = Config::default();
+    cfg.baudrate = BAUD;
+    static TX_BUF: StaticCell<[u8; 256]> = StaticCell::new();
+    static RX_BUF: StaticCell<[u8; 256]> = StaticCell::new();
+    let uart = BufferedUart::new(
+        p.USART1,
+        p.PA10, // RX pin
+        p.PA9,  // TX pin
+        TX_BUF.init([0; 256]),
+        RX_BUF.init([0; 256]),
+        Irqs,
+        cfg,
+    ).unwrap();
+    let yield_period = usart1::setup_and_spawn(BAUD);
+    spawner.spawn(uart_task(uart, &PIPE_HW_TX, &PIPE_HW_RX).unwrap());
+    // END OF HARDWARE UART to the PC
+
+    // INTERNAL HARDWARE UART (USART2)
+    let mut cfg2 = Config::default();
+    cfg2.baudrate = BAUD;
+    static TX_BUF2: StaticCell<[u8; 256]> = StaticCell::new();
+    static RX_BUF2: StaticCell<[u8; 256]> = StaticCell::new();
+
+    let uart2 = BufferedUart::new(
+        p.USART2,
+        p.PD6, // RX
+        p.PA2, // TX
+        TX_BUF2.init([0; 256]),
+        RX_BUF2.init([0; 256]),
+        Irqs2,
+        cfg2,
+    ).unwrap();
+
+    let _ = usart2::setup_and_spawn(BAUD);
+    spawner.spawn(uart_task_internal(uart2, &PIPE_INT_TX, &PIPE_INT_RX).unwrap());
+    info!("USART2 ready");
+    // END OF INTERNAL HARDWARE UART (USART2)
+    
+    // USART1 <-> USART2 bridge
+    spawner.spawn(bridge_usart1_rx_to_usart2_tx(&PIPE_HW_RX, &PIPE_INT_TX).unwrap());
+    spawner.spawn(bridge_usart2_rx_to_usart1_tx(&PIPE_INT_RX, &PIPE_HW_TX).unwrap());
+    info!("USART1 <-> USART2 bridge active");
+    // END OF USART1 <-> USART2 bridge 
+
+    // SOFTWARE UART 
+    let tx = Output::new(p.PB0, Level::High, Speed::VeryHigh);
+    init_tim6_for_uart(p.TIM6, BAUD, TX_OVERSAMPLE);
+    dump_tim6_regs();
+
+    // Safe one-time init from StaticCell
+    let sw_tx_ring: &mut [u32; TX_RING_BYTES] = SW_TX_RING.init([0; TX_RING_BYTES]);
+    
+    let bsrr_ptr = embassy_stm32::pac::GPIOB.bsrr().as_ptr() as *mut u32; // POZOR B REGISTER
+    // let odr_ptr = embassy_stm32::pac::GPIOA.odr().as_ptr() as *mut u32; // NEEDS DECODE CHANGE
+    spawner.spawn(tx_dma_task(p.GPDMA1_CH0, bsrr_ptr, sw_tx_ring, &PIPE_SW_TX).unwrap());
+    // EDN OF SOFTWARE UART 
+
+
+    let mut last_yield = Instant::now();
+    let mut buf = [0u8; 32];
+    let mut counter: u32 = 0;
+
+    loop {
+        info!("tick start");
+        // Timer::after(Duration::from_millis(100)).await;
+        // info!("tick end");
+
+        counter += 1;
+        let msg = if counter % 2 == 0 {
+            b"AAAAA\n"
+        } else {
+            b"Hello\n"
+        };
+        PIPE_SW_TX.write(msg).await;
+        info!("Sent: {:a}", msg);
+
+        Timer::after(Duration::from_secs(3)).await;
+        // Also read any incoming data from SW RX pipe
+        let n2 = PIPE_INT_RX.read(&mut buf).await;
+        if n2 > 0 {
+            info!("HW INT UART RX pipe: {:a}", &buf[..n2]);
+        }
+
+        yield_now().await;
+    }
+}
+
+#[embassy_executor::task]
+pub async fn bridge_usart1_rx_to_usart2_tx(
+    usart1_rx: &'static Pipe<CriticalSectionRawMutex, 1024>,
+    usart2_tx: &'static Pipe<CriticalSectionRawMutex, 1024>,
+) {
+    let mut buf = [0u8; 64];
+    loop {
+        let n = usart1_rx.read(&mut buf).await;
+        if n > 0 {
+            let _ = usart2_tx.write(&buf[..n]).await;
+            info!("bridge: USART1 -> USART2 sent {} bytes", n);
+        }
+    }
+}
+
+#[embassy_executor::task]
+pub async fn bridge_usart2_rx_to_usart1_tx(
+    usart2_rx: &'static Pipe<CriticalSectionRawMutex, 1024>,
+    usart1_tx: &'static Pipe<CriticalSectionRawMutex, 1024>,
+) {
+    let mut buf = [0u8; 64];
+    loop {
+        let n = usart2_rx.read(&mut buf).await;
+        if n > 0 {
+            let _ = usart1_tx.write(&buf[..n]).await;
+            info!("bridge: USART2 -> USART1 sent {} bytes", n);
+        }
+    }
+}